How Can We Help?
Search for answers or browse our help center.
-
Table Base - General
- Actuator lubrication
- Actuator Mount Plate
- Add 1" of Height to a Stationary Base
- Add 5 1/2 Inches to Height
- Add 9 Inches to Height
- Add 9 Inches to Height of the Base
- Add a Push Button Switch to Cut Off Power
- Add a Tape Switch to Tape Switches
- Add Casters to a Base
- Add Corded Pedal to a Rocker
- Add Double Touch if No Board
- Add Hand Switch to Table
- Add Height to Table with a Rocker Pedal
- Add Height with Level Feet
- Add Length and Width Extensions
- Add Length Extensions
- Add Length Extensions to Level Feet
- Add Level Foot
- Add Spacer at Pivot Points
- Add Two Rocker Hand Switches
- Add Width Extensions
- Adding a Corded Pedal to a Table with One Corded Foot Pedal
- Adding a Rocker to an Extended Height Table
- Adding a Second Pressure Pedal
- Adding Bolt-on Width Extensions to a Base
- Adding Casters to Table with Leveling Feet
- Adding Length Extensions
- Adhere Velcro on Skirt to Prevent Rubbing
- Adjust "Limit Down" Micro Switch
- Auto Return - Replace the Switch
- Auto return board compared
- Auto Touch Foot Pedal Trouble Shooting
- Bolt on Foot Pad
- Caster Assembly
- Circuit board wire color template
- CM129 4-motor board diagram
- CM132 4-motor board diagram
- CM132 and Bostek switch compared
- CM132 PC Board Relay Identification Image
- CONVERT CM132 board to 230V
- Flat Cover Panel, with Luxo holes
- How to Add Tape Switches
- How to lubricate scissor pins
- How to move foot section wires on board
- How to move height section wires on board
- How to move lift back section wires on board
- How to replace a circuit board (for boards CM129 and CM132)
- How to temporarily bypass the circuit board
- How to use the Double-Touch Foot Pedal
- Install "Limit Down" Micro Switch
- Install a Micro Switch (For Tables With a Printed Board)
- Install Micro Switch(s) for tables with printed board
- Install Micro Switches
- Limit / micro switch locations
- Mechlock Release
- Move Hand Switch Receptacle to End of Base with the Board
- My table height will not go down when using the foot pedal
- Replace a Pedal Assembly
- Replace Actuator (After February 2004)
- Replace Actuator (February 2004 - Present)
- Replace Actuator and Actuator Adapter
- Replace B-1 Bushings
- Replace Brake Assembly or Worm Gear, noise in elevation motor
- Replace Capacitor
- Replace Circuit Board CM132 with CM129 for tables built between May 2011 to present
- Replace Circuit Board CM132 with CM129 for tables built between Oct 2010 and May 2011
- Replace Corded Pedal
- Replace Corded Wire
- Replace Corded Wire 2 (No Board)
- Replace Corded Wire 45 W/ Board
- Replace Corded Wire 79A
- Replace Power Cord
- Replace Switch in Hand Rocker
- Replace the AutoTouch Board
- Replace the Circuit Board
- Replacing a Corded Pedal
- Replacing a Rocker at Head End with a Corded Pedal
- Replacing a Rocker at Middle of base with a Corded Pedal
- Replacing a rocker foot pedal with corded
- Replacing the B-1 Bushings
- Replacing the Height Actuator in a Base For bases built after February 2004
- Replacing the Lower Scissor Pins
- Replacing the Motor Only
- Replacing the rocker foot pedal switch
- Replacing the Scissor Pins
- RFI Filter
- Rocker Foot Pedal - Align
- Rocker foot pedal alignment
- Shorten the Base
- Squeal noise at the top of height
- Switches Inside
- Threaded Insert, Level Feet
- Troubleshooting auto touch
- Troubleshooting swivel lock
- Wire 2 One Motor, Single Pedal
- Wire diagram for board & pedal assembly for 2, 3 4 motor tables
- Show all articles (81) Collapse Articles
Print
Adding Casters to Table with Leveling Feet
ADDING CASTERS TO TABLE WITH LEVELING FEET
PARTS:
4 qty – #M1838 1 x 1 square pads with countersunk hole
4 qty – H5152 1/4 – 20 x 1 1/4 long” phillips flat head machine screw
4 qty – H509 1/4-20 Nylock nuts
Four square pads should have been included with the caster units if your table has leveling feet. They can be attached with the enclosed bolts after the leveling feet are removed.